HDMI Over IP Range Extender, remote 2G video wall 2G gigabit ethernet LCD display, CAT5, Extend Digital Video and Audio
ST-IPHDMI-R-2G (Front & Back)
ST-IPHDMI-R-2G (Front & Back)

HDMI Over Gigabit IP Extender: Extend up to 333 feet

NTI Part #: ST-IPHDMI-R-2G-Group
The XTENDEX® HDMI Over Gigabit IP Extender multicasts digital video and audio signals to one or more receivers up to 333 feet (101 meters) away over a Second-Generation (2G) 1000BASE-T Gigabit Network connected with CAT5e/6/7 cable. Each HDMI Over Gigabit IP Extender consists of a local unit that connects to an HDMI source, and a remote unit that connects to an HDMI display.
Also known as: HDMI extender, Media center extender, cat5 HDMI monitor extender, remote digital HDMI monitor, HDMI transmitter/receiver, high definition extender, extend video, HDMI range extender, HDMI over IP extender, gigabit HDMI extender.
Product Highlights
  • Visually Lossless 1080p
  • No Image Scaling or JPEG Compression
  • Supports 2-way RS232 Commands
  • No Duplicate IP Addresses on 1000BASE-T Network
  • LAN Bandwidth: 150Mbps
  • Supports video wall installations from 1x2 to 8x8 screens
  • HDMI Over Gigabit IP Extender: Extend up to 333 feetDigital Signage Product
Scroll Down to Get Quote

The XTENDEX® HDMI Over Gigabit IP Extender multicasts digital video and audio signals to one or more receivers up to 333 feet (101 meters) away over a Second-Generation (2G) 1000BASE-T Gigabit Network connected with CAT5e/6/7 cable.

Each HDMI Over Gigabit IP Extender consists of a local unit that connects to an HDMI source, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via CATx or a Point-to-Many connection via a network switch. Support for multiple transmitters requires a managed network switch.

  • Supports HDTV resolutions to 1080p.
  • Ideal solution for digital signage applications.
  • Broadcast real-time HDMI video/audio to multiple display locations.
  • Transmits an HDMI signal over one CAT5e/6/7 cable.
  • Supports video wall installations from 1x2 to 8x8 screens.
  • Plug-and-Play installation allows receivers to find the transmitter automatically on the same network. (Network configuration may be required for Managed network switch.)
  • Easily expandable. Add remote units as you add monitors.
  • No image scaling, the original video signal that is input will be output at the source resolution.
  • Supports 2-way RS232 commands (control software on a PC, or other automated control system hardware such as Control4 or Crestron) to control any devices attached to the matrix using RS232.
  • Integrated mounting wings for ease of installation.
  • Inexpensive CAT5e/6/7 cable replaces bulky video cables.
  • Support for multiple transmitters requires a Managed network switch with VLAN/IGMP support. Standard LAN switches can only support one transmitter.
    • Each VLAN acts as a separate HDMI Over IP Channel on the network.
    • One transmitter can connect up to 200 receivers using cascaded managed network switches.
  • If a non-managed network switch is used for a point-to-many connection, it is not recommended to use other network devices on the same switch as it may cause a degradation in performance.
  • Use a PC to access the built-in HTTP Interface of the managed network switch to control what signal is being watched at each location.
  • Use a Telnet client to access any receiver on the VLAN or network.
  • Customizable EDID table on local unit.
  • HDCP compliant.
  • LAN Bandwidth: 150Mbps for 1080p
  • Protocol: IP, UDP, TCP, ICMP, and IGMP
  • Supports video wall installations from 1x2 to 8x8 screens. (See Control Methods for details.)
Local Unit
  • One female HDMI-A port for source connection.
  • One female 1000Mbps RJ45 port for sending high definition video/audio signals and DDC signal.
  • One female DB9 connector for RS232.
Remote Unit
  • One female HDMI-A port for HDTV or computer display.
  • One female 1000Mbps RJ45 port for receiving high definition video/audio signals and DDC signal.
  • Signal type: HDMI, HDCP compliant.
  • Supports HDTV resolutions to 1080p.
  • Supports multichannel compressed audio (Dolby Digital, DTS, THX) through HDMI compatible TVs or audio receivers.
  • One female DB9 connector for RS232.
Remote Unit with Power over Ethernet
  • One female HDMI-A port for HDTV or computer display.
  • One female 1000Mbps RJ45 port for receiving high definition video/audio signals and DDC signal.
  • Signal type: HDMI, HDCP compliant.
  • Supports HDTV resolutions to 1080p and computer resolutions to 1920x1200.
  • Supports multichannel compressed audio (Dolby Digital, DTS, THX) through HDMI compatible TVs or audio receivers.
  • One female DB9 connector for RS232.
  • Class 2 PoE Compatible (6 watts).
Power
  • Local and remote unit: 100 to 240 VAC at 50 or 60 Hz via AC adapter.
  • Power over Ethernet remote unit (ST-IPHDMI-R-2GPOE): With a switch that supports Power over Ethernet, a power supply is not required at the remote unit.
Cables
  • Use HD-xx-MM cable to connect an HDMI source or display (not included).
  • Use DVI-HD-xx-MM cable to connect a DVI source or display (not included).
  • Use CAT5e/6/7 UTP straight through cable for TIA/EIA-568B wiring terminated with standard RJ45 connectors (not included).
Dimensions WxDxH (in):
  • ST-IPHDMI-L-2G: 5.83x5.19x1.20
  • ST-IPHDMI-R-2G: 5.83x5.19x1.20
  • ST-IPHDMI-R-2GPOE: 7.42x5.19x1.12
Regulatory Approvals
  • CE, FCC, RoHS
Warranty
  • Two years.
Video Wall App
  • Firmware provides video wall applications in sizes ranging from 1x2 to 8x8.
    • Any combination is possible within those limitations (e.g. 2x4, 1x8, 5x5, 6x2).
  • The video wall set-up software is built into the units and can be programmed through any web browser by entering the IP address of the transmitter.
  • With IP-based control systems, the screens can change modes dynamically from video wall modes to standard modes.
  • Works best with progressive video signals such as 480p, 720p and 1080p.
  • Dual mode capability enables higher display quality.
    • Use one transmitter for each row of the video wall to boost picture quality.
  • Ideal digital signage solution for sports bars, emergency response centers, etc.
Managed Ethernet Switch
  • Compatible Managed Ethernet Switches (requires Gigabit for best results)
    • Cisco SG300 Gigabit Series (no stacking)
    • Cisco Catalyst 2960 Gigabit
    • Dell PowerConnect 5400 Series (5424, 5448)
    • Dell PowerConnect 5500 Series (5524, 5524P, 5548, 5548P)
    • Dell PowerConnect 6200 Series (6224, 6224P, 6248, 6248P)
    • Netgear 7000 Series V2 (GSM7224, GSM7228PS, GSM7248, GSM7252PS)
    • Pakedge SW24-GBM, S24P
Matrix Software Lite / Standard / Pro
  • Provides fast and easy switching of video sources.
  • Works as a standalone system or can supplement any RS232-based integrated control system.
  • TCP/IP control offers speed and convenience over any wired or wireless network connection.
  • Features:
    • Lite: supports 8 sources and 12 screens.
    • Standard: supports 16 sources, 16 screens and adds a preset function.
    • Pro: supports 50 sources, 50 screens, includes presets, and adds sequence function and screen groups function.
  • Runs on Windows, Mac and Linux.
    • Mac platform requires OS X 10.4 or newer – Power PC or Intel supported.
    • Windows platform requires Windows 2000 or newer.
Video Wall App Web Browser Configuration Screen Shot
Video Wall App Web Browser Configuration Screen Shot

Application Drawings

  • How to Configure Point-to-Point Connections
    How to Configure Point-to-Point Connections
  • How to Configure Point-to-Many Connections
    Loading image...

Application Notes

  • How to Set-up a Matrix Switch Configuration Using Multiple Transmitters and Receivers and a Managed Network Switch.
    Loading image...
    A managed network switch with VLAN/IGMP support is required to set-up a matrix switch configuration using multiple transmitters and receivers. Each VLAN configuration acts as a separate HDMI Over IP channel on the network. Display receivers attached to a port on the managed network switch can be connected to any chosen VLAN to display that particular HDMI channel. Configuration settings can be controlled via a managed switch's own web interface (where applicable), with IP commands, or the switch's RS232 control port. Control software on a PC or other other home automation controller hardware, such as Control4 or Creston, can be used to simplify the process of commanding the managed network switch.
User Manual:

(0)HDMI Over Gigabit IP Extender via CAT5e/6/7

NTI Part # Local or Remote Qty
ST-IPHDMI-L-2G Local
ST-IPHDMI-R-2G Remote
ST-IPHDMI-R-2GPOE Remote with Power over Ethernet

(0)Matrix Software for HDMI Over Gigabit IP Extender

NTI Part # Description Qty
MTXSW-IPHD2G-L Supports 8 sources and 12 screens
MTXSW-IPHD2G-S Supports 16 sources, 16 screens and preset function
MTXSW-IPHD2G-P Supports 50 sources, 50 screens and presets/sequence/screen groups functions

Collapse all Expand all Related Items :

(0)HDMI Male-Male Cable

NTI Part # Length Qty
HD-3-MM 3 feet
HD-6-MM 6 feet
HD-9-MM 9 feet
HD-14-MM 14 feet

(0)DVI-D Male to HDMI-A Male Single Link Cable

NTI Part # Length Qty
DVI-HD-3-MM 3 feet
DVI-HD-6-MM 6 feet
DVI-HD-10-MM 10 feet
DVI-HD-15-MM 15 feet
Top Please enter a quantity of at least one product
  • Techorium Computing
    • 200 Cochrane Drive, Unit 4,
    • Markham, ON, L3R 8E8, Canada
  • Telephone: (877) 307-4499
  • Fax: (905) 907-4775

Contact Us

© 2013 Network Technologies Inc. All Rights Reserved